Home > FAS3040, Hardware, Home Lab, NetApp > NetApp: Getting the lab FAS3040 up to OnTAP v8.0.5

NetApp: Getting the lab FAS3040 up to OnTAP v8.0.5

 

 

 

This is more for my own notes and cheat-sheets for later.  Now that I’ve gotten the OnTAP v8.x/v7.x RAID LABEL disk issue figured out, time to get the FAS3040 up to OnTAP v8.0.5.

Something to check in advance – if you’ve done a Maintenance Mode “4a” to initialize and create a file system on new disks, it will have done so with 3 disks – 1 + 2 for RAID-DP.  So the size of the aggregate will be the size of 1 disk.  Different OnTAP releases have different minimum disk/vol size requirements.  So depending on the size of the disks, you may or may not have enough space to run the upgrade, without adding disks and expanding the aggregate.

1) Login to the console, and run “setup” if it has not run already.  If you just upgraded to v7.3.x and rebuild the disks and file system, it should run automatically as it doesn’t know anything about itself.

Please enter the new hostname []: NW-FAS3040A
A valid hostname consists of alphanumeric characters [a-zA-Z0-9]
and dash [-].
Please enter the new hostname []: NW-FAS3040A
Do you want to enable IPv6? [n]:
Do you want to configure virtual network interfaces? [n]:
Please enter the IP address for Network Interface e0a []: 10.0.0.71
Please enter the netmask for Network Interface e0a [255.0.0.0]: 255.255.255.0
Should interface e0a take over a partner IP address during failover? [n]:
Please enter media type for e0a {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]:
Please enter flow control for e0a {none, receive, send, full} [full]:
Do you want e0a to support jumbo frames? [n]:
Please enter the IP address for Network Interface e0b []:
Should interface e0b take over a partner IP address during failover? [n]:
Please enter the IP address for Network Interface e0c []:
Should interface e0c take over a partner IP address during failover? [n]:
Please enter the IP address for Network Interface e0d []:
Should interface e0d take over a partner IP address during failover? [n]:
Would you like to continue setup through the web interface? [n]:
Please enter the name or IP address of the IPv4 default gateway: 10.0.0.l
Please enter the IP address for 10.0.0.l []: 10.0.0.1
The administration host is given root access to the filer’s
/etc files for system administration.  To allow /etc root access
to all NFS clients enter RETURN below.
Please enter the name or IP address of the administration host:
Where is the filer located? []: Edm
Do you want to run DNS resolver? [n]: y
Please enter DNS domain name []: netwise.ca
You may enter up to 3 nameservers
Please enter the IP address for first nameserver []: 10.0.0.11
Do you want another nameserver? [n]: y
Please enter the IP address for alternate nameserver []: 10.0.0.12
Do you want another nameserver? [n]:
Do you want to run NIS client? [n]:
This system will send event messages and weekly reports to Network Appliance Technical Support. To disable this feature, enter “options autosupport.support.enable off” within 24 hours. Enabling Autosupport can significantly speed problem determination and resolution should a problem occur on your system. For further information on Autosupport, please see:
http://now.netapp.com/autosupport/
        Press the return key to continue.
The Remote LAN Module (RLM) provides remote management capabilities
including console redirection, logging and power control.
It also extends autosupport by sending
additional system event alerts. Your autosupport settings are used
for sending these alerts via email over the RLM LAN interface.
Would you like to configure the RLM LAN interface [y]: y
Would you like to enable DHCP on the RLM LAN interface [y]: n
Please enter the IP address for the RLM []: 10.0.0.73
Please enter the netmask for the RLM []: 255.255.255.0
Please enter the IP address for the RLM gateway []: 10.0.0.1
The mail host is required by your system to send RLM
alerts and local autosupport email.
Please enter the name or IP address of the mail host [mailhost]:
You may use the autosupport options to configure alert destinations.
The initial aggregate currently contains 3 disks;  you may add more
disks to it later using the “aggr add” command.
Now apply the appropriate licenses to the system and install
the system files (supplied on the Data ONTAP CD-ROM or downloaded
from the NOW site) from a UNIX or Windows host.  When you are
finished, type “download” to install the boot image and
“reboot” to start using the system.
Sun Aug  4 21:19:18 GMT [netif.linkUp:info]: Ethernet e0a: Link up.
add net default: gateway 10.0.0.l
There are 11 spare disks; you may want to use the vol or aggr command
to create new volumes or aggregates or add disks to the existing aggregate.

NW-FAS3040A>

2) Reboot the unit, to get it to start with a clean startup using your settings.
NW-FAS3040A> reboot

Phoenix TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
BIOS version: 2.2.0
Portions Copyright (c) 2006 Network Appliance, Inc. All Rights Reserved
CPU= AMD Opteron(tm) Processor 250 X 2
Testing RAM
512MB RAM tested
4096MB RAM installed
Fixed Disk 0: STEC    NACF1GM1U-B11

Boot Loader version 1.6
Copyright (C) 2000-2003 Broadcom Corporation.
Portions Copyright (C) 2002-2008 NetApp

CPU Type: AMD Opteron(tm) Processor 250

Starting AUTOBOOT press Ctrl-C to abort…
Loading x86_64/kernel/primary.krn:………….0x200000/42699096 0x2ab8958/15834456 0x39d26b0/4665549 0x3e4577d/3 Entry at 0x00202018
Starting program at 0x00202018
Press CTRL-C for special boot menu
Sun Aug  4 21:20:25 GMT [nvram.battery.state:info]: The NVRAM battery is currently ON.
Sun Aug  4 21:20:38 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 1b.
Sun Aug  4 21:20:38 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 1d.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 1c.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 1a.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 0c.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 4a.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 4b.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 4c.
Sun Aug  4 21:20:39 GMT [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 4d.

NetApp Release 7.3.1.1: Mon Apr 20 22:45:56 PDT 2009
Copyright (c) 1992-2008 NetApp.
Starting boot on Sun Aug  4 21:20:22 GMT 2013
add net 127.0.0.0: gateway 127.0.0.1
sparse volume upgrade done. num vol 0.
Vdisk Snap Table for host:0 is initialized
add net default: gateway 10.0.0.l

3) Make sure you’ve put the OnTAP v8.0.5 on a web server on your local network.  Run “software get http://<webserver>/<file>&#8221;

NW-FAS3040A> software get http://10.0.0.3/805_q_image.zip
software: copying to /etc/software/805_q_image.zip
software: 100% file read from location.
software: /etc/software/805_q_image.zip has been copied.

4) Now PERFORM the update, with a “software update <file>”.  This will automatically reboot the filer when complete.

NW-FAS3040A> software update 805_q_image.zip
software: You can cancel this operation by hitting Ctrl-C in the next 6 seconds.
software: Depending on system load, it may take many minutes
software: to complete this operation. Until it finishes, you will
software: not be able to use the console.
software: installing software, this could take a few minutes…
software: Data ONTAP(R) Package Manager Verifier 1
software: Validating metadata entries in /etc/boot/NPM_METADATA.txt
software: Checking sha1 checksum of file checksum file: /etc/boot/NPM_FCSUM-x86-64.sha1.asc
software: Checking sha1 file checksums in /etc/boot/NPM_FCSUM-x86-64.sha1.asc
software: installation of 805_q_image.zip completed.
Mon Aug  5 00:46:05 GMT [cmds.software.installDone:info]: Software: Installation of 805_q_image.zip was completed.
Mon Aug  5 00:46:05 GMT [download.request:notice]: Operator requested download initiated

download: Downloading boot device
Due to the increased size of this release of Data ONTAP, this installation
will take longer than previous installations.  Most installations will
complete in 20-60 minutes.
………………………………………………………………………

………………………………………………………………………

………………………………………………………………………
download: Downloading boot device (Service Area)
……………..
Mon Aug  5 01:24:12 GMT [download.requestDone:notice]: Operator requested download completed
Mon Aug  5 01:24:12 GMT [kern.shutdown:notice]: System shut down because : “reboot”.
Mon Aug  5 01:24:12 GMT [perf.archive.stop:info]: Performance archiver stopped.

Phoenix TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.

 

5) Note that the upgrade automatically rebooted when it completed.  Also in the update:

Boot Loader version 1.8
Copyright (C) 2000-2003 Broadcom Corporation.
Portions Copyright (C) 2002-2009 NetApp

CPU Type: AMD Opteron(tm) Processor 250
> setenv USE_SECONDARY false

Starting AUTOBOOT press Ctrl-C to abort…
Loading x86_64/freebsd/image1/kernel:…0x100000/3606456 0x5707c0/3230448 0x8852b0/1235144 Entry at 0x80148ee0
Loading x86_64/freebsd/image1/platform.ko:0x9b3000/613244 0xb00450/590400 0xa48b80/18056 0xb90690/30048 0xa4d208/1880 0xb97bf0/5640 0xa4d960/57034 0xa5b830/76859 0xa6e470/1568 0xb991f8/4704 0xa6ea90/280 0xb9a458/840 0xa6eba8/976 0xb9a7a0/2928 0xa6ef78/112 0xb9b310/336 0xa6f000/147680 0xb9b460/153792 0xa930e0/425 0xabc500/8832 0xb0035f/237 0xabe780/136440 0xadfc78/132839
Starting program at 0x80148ee0
NetApp Data ONTAP 8.0.5 7-Mode
Copyright (C) 1992-2013 NetApp.
All rights reserved.
*******************************
*                             *
* Press Ctrl-C for Boot Menu. *
*                             *
*******************************

Updating NVRAM firmware from version 09 to version 0b
…………….DONE

 

Some other things to note: The Boot Loader version changes from v1.6 to v1.8.  The LOADER> prompt is automatically set to boot to the new version.  And we can see that the new version is load OnTAP 8.0.5 7-Mode. 

Exactly what we want to see.

Advertisements
Categories: FAS3040, Hardware, Home Lab, NetApp
  1. No comments yet.
  1. No trackbacks yet.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: